Extra deep (for scales) slim drip tray (coloured) complete with long vent tube for Gaggia Classic

Coloured deep drip tray

Extra deep (for scales) slim drip tray (coloured) complete with long vent tube for Gaggia Classic

$0.00
$45.42

View Product Information

Quantity

Earn 0 reward points

We’re sorry we’re out of stock, but we can let you know as soon as this product becomes available again - this will usually be at the weekend

Enter your details below and we’ll email you once this item is back in stock.

Your NameYour Email Address

We've custom designed these deeper and slim / shallow drip trays, and are 3D printing them in COLOURED PLA+ in limited quantities.

Our intention with these is to offer a variety of colours that complement the new Gaggia Classic colours.  They are printed in coloured PLA+ though are not specifically colour matched to the exact colours of the Classic.  Hence the colours may be darker or lighter than the associated Classic colour (eg. noticeably where "blue" is concerned, as the Classic blue is very dark, but our blue drip tray is quite a bright blue).

Colours currently available are:

  • Blue
  • Red
  • White
  • Yellow
  • Grey

This drip tray differs from the normal slim drip tray that we sell in so far as there is a 40mm extension on the front of it - which has two self-adhesive rubber feet underneath (so that it sits on the counter-top).  This design was created and the product produced in response to customers asking for a deeper drip tray with such an extension, so that they could more easily place weighing scales on the drip tray.

They are designed to accept the original black plastic undertray as well as the original stainless steel drip plate from your original Gaggia drip tray.

As they are shallower than the original, at 25mm high - which is around 30mm lower than the original drip-tray, we are also supplying a custom stainless steel vent tube (6mm OD, 0.5mm walls, just like the original - but better quality and with a quality stainless finish rather than chrome) that is longer (158mm) so that it reaches the drip tray perfectly.   This longer vent tube is also available on its own from us here.

Obviously as this part is 3D printed, every part will differ slightly.  Print quality should be good - though due to the printing process and material used, there will be imperfections and texturing visible that are typical to 3D printing with plastic filament such as this.   We have provided images of the drip tray within the Gallery so that you can see a typical finished product and see the expected finish and texture - they are functional rather than necessarily beautiful!   It takes us around a day of 3D printing time to print each deep drip tray, hence production and stock quantities will be limited.

These unfortunately have to be slightly more expensive than the normal slim drip tray, as the printing of these takes significantly more time and uses significantly more material than the standard ones. (We can make only one of these in the time that we can make two normal ones).

NOTE that the PLA+ material that these drip trays are made with is NOT suitable for washing in a dishwasher! The tray will probably deform.  Washing in warm soapy water will be fine.   Whilst the PLA+ material that these drip trays are made from will start to soften slightly at temperatures above around 70c, we design and print these trays with air gaps and low infill to ensure that they remain water-tight and have structural integrity when holding water at close to 100c.

 IMPORTANT We make these on-demand, as ordered - and our 3D printers are always printing something 24x7.  However, even though these may show as in-stock, dispatch of orders for any of our drip-trays may be slightly delayed for a few days due to production timescales - and dispatch preference will be given to orders which also include other items (esp PID kits).


(Note that all photos show the BLACK version - the actual product will be coloured, as per the option selected).

This product contains:

  • Deeper slim drip tray, 25mm high (by 194mm wide and 160mm deep) and 3D printed in coloured PLA+  (without plastic undertray and stainless steel grille), with two adhesive rubber feet on the front underside.
  • Custom 6mm OD x 0.5mm walls (5mm ID) stainless steel vent tube, 158mm long

DISCLAIMER:  The installation of any of our parts or kits, and any modification of any espresso machines undertaken by reference to our installation and/or user guides, should only be conducted by persons with proper electrical safety knowledge who are capable and qualified to undertake such work and modifications.  Many of the components within espresso machines operate at high temperature, high pressure and with mains electrical voltages at high current in the presence of water – any of these could cause serious personal injury, shock, burns, fire, explosion, other property damage and possibly death.  We shall hence not be liable for any damage to property, personal injury or other loss caused by the improper or incorrect use of the aforementioned installation and/or user guides or the provided kit(s) or any of those kit’s component or constituent parts.  By commencing installation of our kit(s) you agree to accept all liability associated with the modification of your espresso machine, and agree to hold us in no way responsible or liable for any loss, damage or injury howsoever, wherever or whenever caused.  You further agree to indemnify us and our agents, officers, directors and employees, immediately and on demand, against all claims, liability, damages, costs and expenses, including legal fees, arising out of any installation, use, misuse or failure of any of our kits or component parts thereof.

Be the first to review this product.

Leave a review

No questions yet - Please use "Ask a Question" if you want to know more or contact us on Chat...

Got any questions - Send them to us here...